2014 Dodge Durango Wont Start

Question

I got through programming and everything for my CHRT6 on my 2014 Dodge Durango with Push Start.

When I hit the lock button 3 times the blue light blinks 3 times, I think the red and yellow lights came on afterwards but I don't remember.

I can hear the fuel pump turn on but the truck doesn't attempt to start.

My settings on Flash Link are

A1-A11 On

C1 On

D1 On

D1.6 On

D1.10 On

D6 On

Answer 1

Do the brake lights turn on when you try to remote start the vehicle?

Comments

I don't think so.

Which guide should I be using? There are multiple that say 2014 durango on them, I think I followed the wrong one......

---

This is your guide to follow: http://cdn.fortin.ca/download/74231/evo-all_ig_tsa_bi_chr6-charger-journey-300_2011-2017_pts_f_74231.pdf

---

Okay that is the guide I followed. What could be stopping my truck from starting? Would the (Mux) Parking Lights wire be doing that?

---

No, when you press lock 3 times does the blue led flash with each lock press? What do the lights on the module do after the blue led flashes 3 times?

---

For each press the blue light does flash.

After the red light comes on and then the yellow light comes on. dDring this time you can hear the fuel pump turn on and then a click). After the click the lights turn off and it cycles through again red, then yellow, fuel pump, click, all off.

I checked and it doesnt seem like my brake lights turn on during the red/yellow phase. (The turn signals do flash with each lock press like it normally would though)

---

Can you please take the green/red wire from the 20 pin connector and connect it to pin 2 of the brake switch (should be a green/brown wire in a black 4 pin connector on the vehicle).

 

Once you make this connection please re test the remote starter.

 

Also turn off option D1.11

---

Just to verify I am taking the Green/Red off of light plug and going to the brake switch?

---

See above image for brake connection.

---

Just to verify that image for the brake connection is not part of the same guide you linked earlier correct? My Green/Red wire is connected somewhere else according to the first guide you listed.

---

Oh yes I see now their are differences in the two guides so that idea will not work.

I suggest calling tech support to go through the torubleshooting process over the phone to get this resolved as quickly as posible. You can ask for me.

1-877-336-7797

Mon-Fro 8-6 EST.

---

Unfortunately I work during the times tech support is open. What kind of other troubleshooting would you have me do over the phone?

---

Ok so i spoke with the engineering.

Please do the following:

1- remove green/red from the parking light wire and connect it to the brake as shown in the picture above.

2- flash 0.81 into the evo-all and re program the module from start to finish including re sending the dcryptor info.

3- you will use the pink/black on the 20 pin with a 1k ohm reissitor for the parking light connection.

 

Once this is done re test the remote starter and let me know your results.

---

Sorry for the delay, life....

 

So I did #1 but I can't get past #2. When I get to step 10 in the program process I am running into an issue. When I hit the start/stop button to turn the ignition on I am not getting the Flashing Blue light. Also when I do turn the ignition on the blue light goes out and everything in my truck seems to go haywire. Windshield wipers turn on, fuel pump turns on, all kinds of warnings pop up on the dash, it says push the clutch in to start the truck(there is no clutch its automatic...)

---

Also when I do turn the ignition on the blue light goes out and everything in my truck seems to go haywire. Windshield wipers turn on, fuel pump turns on, all kinds of warnings pop up on the dash, it says push the clutch in to start the truck(there is no clutch its automatic...)

 

That is caused by bad connections to the CAN-HI or CAN-LOW or both.

 

Which also explains why you cant get the blue led to flash for the can bus programming portion. 

---

I found the wires that were disconnected and fixed them. I got it to program but now when I use the flask link manager the Dcryptor portion isn't working. It count's down from like 7 minutes but stops at 14 seconds every time and does not do anything else. I just let it sit for 30 minutes and it sat at 14s the whole time. I restarted the dcryptor process multiple times but nothing has changed.

---

Your dcryptor is done on our end (red text): https://fortin.ca/en/support/001A06783832/

 

You need to go back into Dcrpytor and click the Update Unit button (not the Flash button)

 

When initially sending the dcryptor, there was an empty check box with a note Automatically Udpate Unit When Ready. Clicking on the checkbox would prevent needing having to click Update Unit. 

---

I did have the Automatic update checked off all 5 times I tried it. Every time it stopped at 14,13, or 4 seconds left and never moved. It sat at 4 seconds for over 12 hours over the weekend.

 

I just reconnected my dcryptor and had to "Send Data" again but this time it only took 12 seconds to get to the updating portion compared to the 54 minutes on Saturday when it never even got to update.

 

All good now. Thank you for the assistance in this.